Products tagged with werkzeug

Watchmakers tap set
Taps in the following sizes:
M1 / M1,2 / M1,4 / M1,6 / M1,8 / M2 / M2.5 / M3 / M3.5
Holes should be pre-drilled 0.1-0.4mm smaller.
Taps can be clamped in a (mini) tap wrench.

Miter cutter

Ideal for miter cutting (multi angle) of small profiles and strips of wood, plastic, styrene, etc.

Comes with 2 sheffield carbon steel blades. (1x single sharpened, 1x double sharpened)

Dimension: 210mm x 210mm

Cutting length blad

Watchmakers tap set
Taps and die in the following sizes:
0,7mm / 0,8mm / 0,9mm / 1.0mm / 1.1mm / 1.2mm / 1.3mm / 1.4mm / 1.5mm / 1.6mm / 1.7mm / 1.8mm / 1.9mm / 2.0 mm
Holes should be pre-drilled 0.1mm smaller.
Taps can be clamped in a drill chuck, fo

Diamond Burs + diamond disks - 25 parts

18 Diamond Burs
5 diamond disks (metal)
2 Holders
Base thicknes 3mm
Ideal for Proxxon, Demel and comparable machines.

Mini drills 10 st. 0.3-3.0 mm

Fretsaw

Fretsaw to be used to saw wood profiles, plastic and fine metals.

Glass fibre cleaning pin

For cleaning the connection areas on circuit boards, cleaning contacts of all kinds, removing residues on metal templates.

In plastic modelling used to sand over applied glue on models.
When in use, only the tip of the...

Mini Machinist Square

Size ca.20x25mm

Sandpaper file

3 Variants:
120 Grid
180 Grid
240 Grid

Single sanding belts also available

Blades for Hobby knifes and scalpel blades
Packed per 5 Pieces
Choose from drop-down list:
Hobby knife #1:A1, A2, A3, A4, A5
Hobby knife #2:B1, B2, B3, B4, B5

Scalpel handle 3&7:10,10A, 11, 12, 15
Scalpel handle 4:20

Masking Tape
Acid free, leaves no glue residue
Length: 18 meter

Available sizes:
1mm
2mm
3mm
6mm
10mm

Humbrol Maskol
Humbrol Maskol is a liquid. when dried it looks like a kind of rubber film. This allows you to easily protect parts of your model when you are going to paint or for example want to apply camouflage. It is recommended not to leave the dried

Hand drill with chuck and rotating base

For drills from 0.3 - 2.5 mm

Nail press 2mm / 3mm
A nail press is the solution if you need to hammer small nails and nails into a delicate surface. Or if it is dangerous to use a hammer. The nail press has a magnetic head that holds the nail in place.
Make your choice:
Blue - for

Diamond Burs - 30 pieces in box

Base thicknes 3mm

Ideal for Proxxon, Demel and comparable machines.

Watchmakers tap set
Taps and die in the following sizes:
0.6mm / 0.7mm / 0.8mm / 0.9mm / 1.0mm
Holes should be pre-drilled 0.1mm smaller.
Taps can be clamped in a drill chuck, for example: https://www.marks-miniatures.com/en/hand-drill-with-chuck-and-

Machinist Square

Size ca.57x77mm

Mitre box

For small tubes and rods
45 and 90 degree sawing with adjustable stop

Precision hand vice

One side has a horizontal and vertical groove for clamping round materials.

With sturdy wooden handle (hexagon) for good grip.

Jaw width: 10mm

Usable jaw depth: 18mm

Max. Opening: 14mm

Miter sanding aid - angle sanding
The angle can be adjusted.
The handpiece has a slide (stop).
Comes with a set of 3 extra sanding belts:
150 Grid
240 Grid
320 Grid
Sanding belt set is also available separately.

Ideal for profiles in styrene, wo

Circular saws mini - 6pcs

Ideal for Proxxon, Dremel, etc.

Bending springs for tubes

For evenly bending brass, copper and tubes without kinking.

Beforehand, the part of the tube to be bent must be softened by heating it with a flame. Then let the tube cool down. After cooling, the bending can begin.

Meth

Drill set 2.35 mm Shank

0.6mm, 0.7mm, 0.8mm, 0.9mm, 1.0mm, 1.2mm, 1.5mm, 1.8mm, 2.0mm, 2.3mm

Rotating platform 25 cm