Your cart is currently empty
Humbrol Maskol Humbrol Maskol is a liquid. when dried it looks like a kind of rubber film. This allows you to easily protect parts of your model when you are going to paint or for example want to apply camouflage. It is recommended not to leave the dried
Polystyrene cutter / Foam Cutter / 3 in 1 set Ideal for cutting and processing polystyrene, tempex and foam. Supplied with power supply, support, spare cutting wire and 3 different attachments: - to cut - to model - for soldering
Microscale Micro Sol - Decalfluïd Micro Sol setting solution is for the most difficult irregular surfaces to be found on models. It completely softens the Microscale Decal, allowing it to drape down onto the surface of the model, conforming perfectly to
Milliput is one of the best known epoxy putty products for modeling. Milliput also consists of two components and by mixing well (5 min. Good kneading) the material will slowly harden, after which it is fully cured after 3 hours. By keeping the putty cool
Airbrush with 0.2 - 0,3 and 0.5mm needle/nozzle and hose Fine airbrush, double action, equipped with adjustable needle stop and solid 7 ml. metal paintcup. Suitable for very fine to medium detail work. The kit comes with mounted nozzle and needle 0.3mm a
Mini Compressor Single piston oil-free Mini Compressor. Without air reservoir (pressure vessel), the regulator of the output pressure, which is equipped with the filter and pressure gauge (manometer) Low volume during operation, can be used also in the e
Magnifying glasses with LED lighting 1.0x, 1.5x, 2.0x, 2.5x, 3.5x Magnifying glasses with 5 interchangeable lenses and 2 LEDs - LED light switchable and pivotable - Rotatable lens holder - Glasses arms can be replaced by a headband - Interchangeable lens
Hand vice - opens rotated Vice: Steel Width of Jaws:15mm Handle: Wood Max. Opening: 10mm Hand vice opens the jaws when rotated Serrated haws with a vee Hollowed Handle to feed longer material trough the handle to the vice
Mini Allen Key Screwdriver Please choose your size: 1.5mm 2.0mm 2.5mm 3.0mm
LAMP WITH MAGNIFYING GLASS 5 DIOPTRE - DAYLIGHT - 22W WHITE This magnifying lamp is designed as an aid for all kinds of precision applications from health care to precision engineering. It's also ideal for home applications. It comes with a 5-dioptre len
Sandpaper file 3 Variants: 120 Grid 180 Grid 240 Grid Single sanding belts also available
Glue Applicator 12 Pcs. For a precise application of cyanoacrylate glue. (cyanoacrylate glue not included)
Watchmakers tap set Taps in the following sizes: M1 / M1,2 / M1,4 / M1,6 / M1,8 / M2 / M2.5 / M3 / M3.5 Holes should be pre-drilled 0.1-0.4mm smaller. Taps can be clamped in a (mini) tap wrench.
Copper wire set 1x 0.35mm smooth wire 1x 0.8mm wrapped wire. Ideal for depicting steel cables. Length: 55cm per wire
Bending springs for tubes For evenly bending brass, copper and tubes without kinking. Beforehand, the part of the tube to be bent must be softened by heating it with a flame. Then let the tube cool down. After cooling, the bending can begin. Method: S
Mini vise Jaw width 40mm Maximum opening: 30 mm Can be mounted on the table with the screw holes.
Triangle screwdriver bit set 1.8mm / 2.0mm / 2.3mm /2.7mm /3.0mm often used to remove base plates from scale model cars
Mini open end- and ring spanner set 3.2mm / 4mm / 5mm / 5.5mm / 6mm / 7mm / 8mm / 9mm /10mm Thin version, 1.6mm thick.
Mini Anvil Double horn anvil for precision work. Excellent quality. hardened. Widely used by watchmakers, jewelers and hobbyists.
Colle 21 anaerobic cyanoacrylate glue - 21 gram COLLE 21 is an ANAEROBIC glue, It works with pressure, which gives you the time to correctly position your assemblies. Assembly without the pressure of 2 surfaces. The pressure made (15 to 45 seconds) will
Photo Etched parts Bender (Large) with 4 bending aids. Has been specially developed for model building using photo etch parts allowing the brass to be held and bent accurately into many different shapes. Measures 79mm x 162mm
Hand Vice deluxe Vice: Aluminium Handpiece: wood Pins: 8 Normal objects can be clamped between the two halfs. The Pins could be used to clamb round and uneven objects. Maximum opening halfs:18mm Maximum opening between pins:51mm